Skip to content

Smartctl Open Device Dev Sda Failed Dell Or Megaraid Controller Please Try Adding 39d Megaraid N 39 Extra Quality _top_ -

When the operating system reads /dev/sda , it is interacting with an emulated, unified virtual drive, not a physical piece of silicone or spinning media.

This applies to any LSI MegaRAID card (e.g., 9260, 9361) under Linux. For HP SmartArray, use -d cciss,N ; for 3ware, use -d 3ware,N .

Most SATA drives behind a MegaRAID controller respond seamlessly to the -d megaraid,N flag.

Dell PERC controllers are hardware RAID controllers. The OS doesn't see the raw physical disk; it sees a "Logical Drive" created by the PERC firmware. smartctl requires direct ATA/SCSI commands, which the PERC controller intercepts. When the operating system reads /dev/sda , it

This will output the enclosure device ID, which is usually a numerical value.

To fix this, you must tell smartctl to bypass the abstraction and target a specific physical disk using the -d megaraid,N flag. 1. Find the Physical Drive IDs

If you want the S.M.A.R.T. daemon ( smartd ) to continuously monitor your drives behind a MegaRAID controller and alert you of failures, you must modify its configuration file. Most SATA drives behind a MegaRAID controller respond

Dell and MegaRAID controllers use a proprietary interface to manage their RAID configurations, which can make it challenging for utilities like smartctl to access the drives. By default, these controllers do not allow direct access to the drives, which leads to the "open device" error.

If you have perccli (Dell) or storcli installed, run: /opt/MegaRAID/perccli/perccli64 /c0 /eall /sall show Use code with caution. Copied to clipboard Look for the DID (Device ID) or Slot Number column. 2. Run the Correct Command

Smartctl open device: /dev/sda failed: DELL or MegaRaid controller, please try adding '-d megaraid,N' smartctl requires direct ATA/SCSI commands, which the PERC

You can try to list all drives behind the controller to identify the correct N value (starting from 0, 1, 2...): smartctl -a -d megaraid,0 /dev/sda Use code with caution.

: This represents the or physical slot number on the controller. How to Find the Correct "N"

When the operating system reads /dev/sda , it is interacting with an emulated, unified virtual drive, not a physical piece of silicone or spinning media.

This applies to any LSI MegaRAID card (e.g., 9260, 9361) under Linux. For HP SmartArray, use -d cciss,N ; for 3ware, use -d 3ware,N .

Most SATA drives behind a MegaRAID controller respond seamlessly to the -d megaraid,N flag.

Dell PERC controllers are hardware RAID controllers. The OS doesn't see the raw physical disk; it sees a "Logical Drive" created by the PERC firmware. smartctl requires direct ATA/SCSI commands, which the PERC controller intercepts.

This will output the enclosure device ID, which is usually a numerical value.

To fix this, you must tell smartctl to bypass the abstraction and target a specific physical disk using the -d megaraid,N flag. 1. Find the Physical Drive IDs

If you want the S.M.A.R.T. daemon ( smartd ) to continuously monitor your drives behind a MegaRAID controller and alert you of failures, you must modify its configuration file.

Dell and MegaRAID controllers use a proprietary interface to manage their RAID configurations, which can make it challenging for utilities like smartctl to access the drives. By default, these controllers do not allow direct access to the drives, which leads to the "open device" error.

If you have perccli (Dell) or storcli installed, run: /opt/MegaRAID/perccli/perccli64 /c0 /eall /sall show Use code with caution. Copied to clipboard Look for the DID (Device ID) or Slot Number column. 2. Run the Correct Command

Smartctl open device: /dev/sda failed: DELL or MegaRaid controller, please try adding '-d megaraid,N'

You can try to list all drives behind the controller to identify the correct N value (starting from 0, 1, 2...): smartctl -a -d megaraid,0 /dev/sda Use code with caution.

: This represents the or physical slot number on the controller. How to Find the Correct "N"